You are here

Pallet of Pavemark Thermoplastic Extrude Bags

overview example image of a pallet of PaveMark Thermoplastic Bags
SKU: 884490

Ordering by Phone? Make sure you have the right product. Check the Product SKU List below.

Pavemark Thermoplastic Extrude Bags Pallet
List price: $2799
Free Shipping to lower US 48
In Stock
Choose the color you would like to purchase
Have a question about this product?Ask it now!
Quick Overview: 
  • Sold as a pallet of 40 bags totaling 2000 lbs
  • Each heat degradable bag weighs 50 lbs
  • Perfect for municipalities or thermoplastic road crews
  • Choose between White or Yellow


Product Description:
Ennis-Flint’s Pavemark is and alkyd extrude thermoplastic for pavement marking that is a 100% solids material blend of binder, pigments, and glass beads. Pavemark is melted to a temperature of at least 425°F (218°C) in a melting kettle, mixed well and then applied in a molten / liquid state to the pavement.

Roadway surface temperature at the time of application should typically be a minimum of 50°F (10°C) and rising due to the quick setting nature of the cooled material once applied. Upon cooling to normal pavement temperature, thermoplastic provides a very durable marking material for low and high volume traffic areas which makes it an excellent product for both longevity and cost savings.

Pavemark is designed to be used in Thermoplastic Extruders such as the Titan ThermoMark 300 and melted in a kettle with agitation for best mixing results.

Thermoplastic is sold in one-ton increments (2000 pounds). The ton is divided into 40 heat degradable bags each weighing approximately 50 pounds.

The shelf life of the product is one year from date of manufacture with proper storage. Proper storage includes inside or covered to prevent from moisture, and below 120F. Outside storage for short intervals is acceptable as long as the material is kept dry. The older the material, more agitation and dwell time is required to fully melt and mix the granular ingredients.

Conditions for Application:
All surfaces must be clean, dry and free from oil, grease, antifreeze, loose sand, aggregate and chipping/peeling existing striping. Any curing compounds used on new concrete must be mechanically abraded off prior to striping and use of a primer is strongly suggested. Concrete should be allowed to cure for 14 days. When in doubt, always test adhesion. While thermoplastic may be installed behind the paver once the mat cools, new asphalt should be allowed to cure for a minimum of 14 days to maximize adhesion and durability.

One-Ton of thermoplastic yields approximately 6000 feet of 4” stripe @ 90 mils – textured surfaces will decrease the coverage yield.

Product Details:
Product Type: Alkyd /Extrude Thermoplastic
Product Code: 884490 884685
Product Color: White Lead-Free Yellow
Description: TM WHT ALK AA extrude
TM LF YEL ALK AA extrude
Specification: Meets AASHTO M-249
Effective Date: May 31, 2017

Physical Characteristics:
% Binder: 18% minimum
% Glass: 30% minimum
Intermix glass spec: M-247 type I
% TiO2 in the white: 10% minimum
595B color, white: 17886
595B color, yellow: 13538
White Reflectance (Y value): 75 minimum
Yellow Reflectance (Y value): 45 minimum
Minimum Impact Resistance: 10 inch pounds
Softening Point: 200-230°F
Yellowness index, white: 0.12 maximum
Skid Resistance: 45 BPN minimum
Dry Time: With drop on glass beads applied, the thermoplastic material shall be sufficiently tack-free to carry traffic in not more than 2 minutes when pavement surface temperature is at 50°F, and not more than 10 minutes whenpavement surface temperature is 130ºF.

Applying a test strip to determine if surface is dry enough; if there has been rain in the last 24 hours.

  • Do not apply if hot material shows moisture bubbles.
  • Do not heat thermoplastic above 450°F.
  • Do not apply when road and ambient temperatures are below 50°F.
  • Do not apply when temperatures are near or below the dew point.
  • Material at application is hot – please wear personal protective equipment as described in MSDS

Product SKU List

These are the SKU numbers to give if you plan to buy over the phone. To see pricing changes (if any), click on the "drop down" arrow in the Add to Cart section above.








  • Non-flammable and below 150 VOC

  • Demonstrates excellent bead retention and abrasion resistance

  • Fast set up keeps traffic control to a minimum when striping

  • Can be used for symbols, legends and lane marking

  • A low cost per useful life durable form of delineation


Material and Safey Data Sheets (MSDS/SDS):
Shipping Weight
Weight: 2070 lb
Shipping Dimensions
Dimensions: 48 in × 48 in × 48 in